Wall protection film for painted surfaces, clear, transparent

Geometry Linear metre

Rounded corners

Width [cm]

Height [cm]

Cutting possible on request
Unfortunately, your desired size cannot be ordered via the online shop. However, we can still offer you the dimensions. Please ask our customer service at info@velken.shop.

from €1.46

Price per m² from: €27.92 Price per m²: €25.13 Price per m²: €27.92 incl. VAT plus shipping costs. Item no. 753130

Delivery time approx. 3-6 days

CNC cutting accurate to the millimetre

Properties of this film

Colour	transparent
Liability	self-adhesive
Protection from	Damage
Mounting side	Indoor assembly, Outdoor installation
Application	Stone, Bodywork, Wood

Questionst?
Start WhatsApp chat

Extremely resilient wall protection film This wall protection film is specially developed for...

Close menu

Extremely resilient wall protection film

This wall protection film is specially developed for bonding to painted or powder-coated surfaces that can be flat and slightly curved. For example, this film can protect painted doors, kitchen fronts or even painted wood from dirt.

The extreme tear resistance is what sets this wall protection film apart. According to DIN EN ISO 527, it withstands loads in the longitudinal and transverse directions of > 34 MPa. The elongation at break was determined to be 550% for the longitudinal and transverse elongation. The protective film is therefore suitable for tough everyday use; even short-term contact with solvents or chemicals does not affect this wall protection film.

Other advantages of this film:

Easy to assemble and extremely resilient
The surface is very fine and also scratch-resistant
It does not shrink and does not wrinkle even after years
The film is dirt-repellent and easy to care for

Product information

The surface to be glued must be free of dust, grease or other contaminants that could affect the adhesive strength of the material. New paintwork must be dried or completely hardened. To determine compatibility, application tests must be carried out with the intended paints. It is advisable not to apply foil to repainted surfaces, as removing the foil may cause damage to the paint. The repainted paint often does not adhere to the underlying filler as well as the original paint that was applied at the factory.

Included in delivery

Assembly instructions

The optional assembly squeegee with felt edge is not included in the delivery. We recommend ordering this for assembly.
Any waste is not included in the scope of delivery.

Technical data and information at a glance...

Close menu

Haltbarkeit

Der Hersteller weist eine Haltbarkeit von 5 Jahren aus.

Technische Daten
Material	Polyurethan-Folie
Foliendicke	ca. 130 µm
Formbeständigkeit (FINAT TM 14)	Verklebt auf Stahl max. 0,2mm Schrumpf
Temperaturbeständigkeit	Verklebt auf Aluminium, -40°C bis + 100°C keine Veränderung
Seewasserbeständigkeit (DIN 50021)	Verklebt auf Aluminium, nach 100 h/23° C keine Veränderung
Lösemittel- / Chemikalienbeständigkeit	Bei Raumtemperatur, 72h nach Verklebung auf Aluminium kurzzeitig beständig gegen die meisten Öle, Fette, Kraftstoffe, aliphatische Lösungsmittel, schwachen Säuren, Salze und Alkalien
Reißfestigkeit (DIN EN ISO 527)	Längs: > 34 MPa Quer: > 34 MPa
Reißdehnung (DIN EN ISO 527)	Längs: > 550% Quer: > 550%
Haltklebstoff	Solvent Polyacrylat, permanent
Klebkraft	18 N/25mm
Verklebungstemperatur	> + 10° C

How to mount this film on the window...

Close menu

Montagevideo starten — Installation video for window films. Click on the picture to start.

Assembly instructions for Protective films (self-adhesive)

You will need the following items

Plastic bottle with hand sprayer, adhesive tape, paper towels (not included)
Transfer concentrate (not included)
Glass cleaner (not included) or commercially available glass cleaner
Installation squeegee and glass scraper blade (included free of charge in the delivery).

Installation tips

Two people should carry out the installation!
Do not install any film at temperatures on the installation side below +6° C.

Fill the spray bottle with 0.5 litres of water and add the transfer concentrate (30 ml) (enough for approx. 6 to 7 m² of glass surface).
Thoroughly clean the glass with commercial or our glass cleaner!
Remove all sticky particles (e.g. paint or fly dirt) preferably with the glass scraper blade. No dirt residues should remain on the glass!
The sandblasting foil consists of the mostly white backing paper and the actual sandblasting foil.
Now place the sandblasting foil with the view side down on the glass pane or similar. You are now looking at the back of the film.
Then carefully and slowly peel off the backing paper at as shallow an angle as possible until it is about halfway along the entire length of the film. Cut the backing paper and stick it back onto the sandblasting film with a gap of about 2 cm to the remaining backing paper.
Now hold the in place while the 2nd person starting from the corner, and at the same time spray the adhesive side of the that is now exposed with the liquid.
Afterwards, the glass pane (surface to be pasted) must be sprayed with the liquid. Do not be sparing with the liquid, the film and pane should be well wet.
Place the on the glass, the film should slide back and forth well, otherwise spray the glass again.
Now spray the other side of the as well, this will make it easier for you to work with the mounting squeegee.
Now press the liquid out evenly with the mounting squeegee from the centre to the right and to the left. Make sure that there is no residual water left under the film! Repeat this procedure several times to remove even invisible water residues. When doing this, wrap the supplied squeegee with a paper towel to avoid any scratches.
Carefully wipe the edges and the foil with a soft cloth. If necessary, press the edges again with the mounting squeegee.
Now let the dry for three days without touching it.
Wait two weeks before cleaning the film for the first time and never use hard objects (brush or blade) to clean it. Commercially available glass cleaners can be used.

FAQ`s about the installation

Films that are no larger than 1m² can be installed alone without any problems.
For larger pieces, it is recommended that two people carry out the installation. This makes it easier to handle the film and place it on the pane.

First, clean your windows really thoroughly with glass cleaner. Then go over the entire window pane again with our supplied glass scraper blade to remove any hard-core impurities on the pane (such as fly droppings). These fine stains are often invisible to the naked eye and you will be amazed at what the blade still removes.

In addition, do not lay the after peeling off (covers the adhesive side for transport) on the floor to get it wet. Rather, pull a table nearby to spray the film on. On the floor you will always stir up very fine dust particles, which will then settle on the adhesive side facing upwards. These dust particles can later show up on the pane under the , which is something to avoid.

Alternatively, you should at least use a pH-neutral cleaner. We do not recommend installation without any additive at all, which increases the gliding properties of the water!

We strongly advise against the use of water diluted with detergent. This can lead to streaking due to a reaction with the film adhesive.

No, this is not necessary as long as you have sprayed the adhesive side of the window film and your glass sufficiently wet. Due to the moisture, the adhesive has no adhesive effect, which makes it easy to move the film and position it precisely. It is even possible to remove the film from the glass again and reapply it.

The bubbles consist of residual liquid that was not pressed out from under the film when it was applied. Over time, these run down between the already drying film adhesive as far as they can under the film and collect in some places. The bubbles disappear by themselves when the remaining liquid diffuses through the film to the outside. Depending on the outside temperature and sunlight, this can take up to three or more weeks before the film fits like a second skin.

In any case, you should wait this time and do nothing. In most cases, the blisters disappear all by themselves!

The window film itself can be easily removed. To do this, detach one corner and fold it over directly. The film can then be removed from the glass at as flat an angle as possible.

It is possible that residues of the film adhesive remain in some places. These can be soaked with our adhesive remover or acetone and then removed again with a glass scraper or ceramic field scraper. You will find detailed instructions on how to remove window films on our homepage in the FAQ`s.

Order a product sample...

Close menu

We will be happy to send you a free sample of this and up to four other films without obligation.
The samples are approx. 9 x 9 cm in size and will be sent to you free of charge and without obligation by letter post.